Featured post

Types of mechanical forces

-
A force exerted on a body can cause a change in either the shape or the motion of the body.The unit of force in SI system is the Newton(N) and CGS system is dyne.No solid body is perfectly rigid and when force are applied to it,changes in dimension occur.such changes are not always perceptible to the human eye since they are negligible. For the example,The span of a bridge will sag under the weight of a vehicle and a spanner will bend slightly when tightening a nut. It is also important for civil engineers and designers to appreciate the effects of forces on materials.Together with their mechanical properties of the materials. There three main types of mechanical forces that can act on a body.They are 1)Tensile force 2) compressive force and 3) shear force
2 comments

What is lathe machine?

-


Lathe Machine Points : Lathe Machine, Definition Lathe machine is a power driven regular machine tool used to make cylindrical conical and flat surfaces by a sharp edge single point tool which is fed next to a turning work piece together held in the holding devices.Taper turning, straight turning, facing drilling, reaming boring, thread cutting. Forming and knurling are several of the familiar operations perform on a lathe machine.

Comments

  1. Anonymous5 June 2017 at 01:06

    I’d like to thank you for writing on lathe machine. The information you provided was very useful. I will visit again in the near future.
    soda lime glass properties

    ReplyDelete
  2. bradshawjohn5 June 2017 at 02:09

    Thanks for helping us understand topic on lathe machine. You have written it in a way that makes it very simple to understand.
    fused silica polishing

    ReplyDelete
  3. Anonymous5 June 2017 at 02:41

    The issues you’ve raised in this blog are very real. People usually hesitate to write on such topics but you did wonderful work.

    infrared optical wafers

    ReplyDelete
  4. bradshawjohn5 June 2017 at 03:13

    Thank you so much for the sharing information of lathe machine. All contents were expressed in a clear n simplified manner n it was meaningful too.

    thin fused silica wafers

    ReplyDelete
  5. Anonymous5 June 2017 at 04:01

    Hey! Thank you so much for sharing this blog with us. It provides a big collection of useful information.

    edge deburring machine

    ReplyDelete
  6. Anonymous6 June 2017 at 06:07

    Many congratulations that you could manage to write on this sensible issue. I am taking the helping tips and hope it will be useful for others too.

    shim spacers

    ReplyDelete
  7. Anonymous8 June 2017 at 03:17

    very useful information you have given through this blog regarding education sector.
    black light material

    ReplyDelete
  8. bradshawjohn11 June 2017 at 23:35

    You did not divert from the topic even once which I have not seen in many other writers. Also the subject knowledge is appreciable.

    thin ceramic substrates

    ReplyDelete
  9. Kathleen O'Connor12 June 2017 at 00:53

    I guess your blog has clear the confusion in very simpler way. Thank you on behalf of them.

    optical surface roughness metrology service

    ReplyDelete
  10. bradshawjohn6 November 2017 at 06:09

    I was searching for the matter you shared through blog. It is quite interesting and obviously very informative for me. Thanks you very much!
    quartz substrate

    ReplyDelete
  11. mike23 August 2018 at 03:44


    Great information. Thanks for providing us such useful information. Keep up the good work and continue providing us more quality information from time to time.
    aluminum nitride machining

    ReplyDelete

Post a Comment

Popular posts from this blog

Tailstock

-
Image
The tailstock is located on right side of the bed i.e.right hand side of the operator. The main purpose of a tailstock on an engine lathe is to support free end of a work during operation.it is also used to hold tools for making holes (twist drills,reamers) adjusted along the bed of the lathe accommodate different lengths of stock.it is provided with set over screw at its base for taper turning alignment.it has cast iron body with bore to accommodate tailstock spindle,and the top portion contains the spindle,tailstock hand wheel, and a spindle clamp for locking the spindle in position. The end of the spindle has a taper bore for holding dead centre,taper shank drills and other tools.the spindle can centre,taper shank drills and other tools.The spindle can be moved in and out of the tailstock by the rotation of hand wheel in anticlockwise and clock wise direction respectively.A tailstock is shown in fig.
Read more

ADVANTAGES AND LIMITATIONS OF BROACHING:

-
Broaching is an interesting machining process which is used in mass production. It has certain advantages and limitations as compared to the other machining processes.these are given below. ADVANTAGES : 1) Fast and simple process. 2)High degree of accuracy and finish is possible. 3)Any shape of profile can be easily machined. 4) Machining process is completed with one stroke of broach. 5) Life of broach tool is high. 6)Cutting temperature and tool wear is low. 7) Doesn't require a highly skilled operator. 8)Cutting force acts in the clamping direction I.e.,it doesn't tends to lift the workpiece from fixture. 9)cutting fluids can be applied more easily and effectively. 10)Most economical for mass production of components. LIMITATIONS: 1) Not economical for small quantity productions. 2)Cost of broach is high. 3) Tool grinding (broach sharpening) is difficult and expensive. 4) Not suitable to machine a surface having obstruction. 5) The work m...
Read more

METHODS OF APPLICATIONS OF CUTTING FLUIDS :

-
Image
The method of application of a cutting fluid is very important and depends on the particular operation. These methods vary from hand applications such as use of brush or oil-can to high pressure applications.For high production. The following methods are used.    1)Flood method,    2) Jet method,and    3) Mist method. 1) Flood method : In this method,a reciprocating pump is used to force the coolant over the work and tool.The outlet of the pump is connected to a nozzle through flexible pipe.The nozzle can be adjusted to direct the stream of the fluid at the cutting zone.This is the most common method of application of cutting fluid. 2) jet method : In jet method,a small jet of fluid at high speed is directed at the point of metal separation from the underneath the tool.In high-speed jet system gear or vane type pump is used to maintain high pressure. 3) Mist method : In mist method,the fluid is passed through a specially designed ...
Read more